The machine is suitable for counting the labels when checking or storage the labels in roll. The machine is special designed according to the process of the labeling machine.
The structure of the machine: consist of stepping speed control motor, electronic counting machine, optoelectronic switch. The main system is controlled by the PLC and the touch screen.
1) 設備電路由總電源開關、顯示器、正反轉開關組成。
— The circuit is consist of power switch, monitor, clockwise and anti-clockwise switch.
2) 計數器為顯示器計數器。
— The counter adopts display screen to show the counting number.
3) 標簽規格:標簽卷筒芯內徑:Ф76mm
標簽紙卷外徑:較大Ф300mm
標簽卷筒紙高度:150mm以內
— Specifications of the labels: Inner diameter: Ф76mm
— Fix the label roll according to the graphical representation, adjust the height of every part.
Put the label on the driven plate, preparing an empty label roll, which inner diameter is 76 mm, height is consistent with the label, put the empty roll on the drive plate, wind the label through the leading wheel- optical - leading wheel, winding on the empty label roll (recommended leave a period of blank paper without label at the beginning and the end, so that reduce the error), winding finished, put the organic glass cover on the roll(leave a bit space between the plate and the roll, otherwise the plate will be press on the label, and tear the paper), then lock the screw, insert the fixed steel rod, choose appropriate socket when insert the steel rod, prevent the skid phenomenon during the winding process.
2) 檢查標簽位置是否正確。
— Check outif the label position is correct.
3) 開電源,點擊工作畫面到數標畫面,再點擊啟動。
— Turn on the power supply, press the working page to the counting page, then click the key of run.
4) 確認無故障后可以正常生產。
— After confirmed trouble-free can operate normally.
— Max speed:means the speed in the beginning, can be adjusted according to need, if this parameter changed, it will take effect after clear the cumulative quantity and the current quantity.Do not set the parameter too high nor too slow, among 500 HZto 600 HZ is appropriate.
—Time interval: during the counting process, the diameter of the roll on the drive plate is getting larger and larger, but the RPM of the motor is fixed, so when the diameter getting larger, then the circumference (that is length go through the photoelectricity) will get longer, then the system will count more labels, the detector response speed can not keep up with, so need to reduce the equipment running speed, the time interval parameter is used to set how long the speed will reduce. Do not set the parameter too high nor too slow, it is mainly depend on the length of the label, the label longer can slightly higher, short tag can be slightly lower, among40Sto 60S is appropriate..
— Velocity change: this parameter means the frequency it decrease during the time interval,then after the time intervalreached, the total speed will decrease the number you set. Do not set the parameter too high nor too slow, among 20 to 40 is appropriate.
— For example: The max speed the 520 HZ, the time interval is 50S, the velocity change is 20 HZ.
— Explanation:The speed at the beginning is 520HZ, when running after the 50S, speed reduced to 500HZ, after 100S speed reduced to 480 HZ.
— Set the screen to the counting parameter image, press SET key, then pitch on the parameter needing to change, press SET button to enter, select the data needs to adjust, then input the data, after adjusted, press key of ENT to confirm. After confirmation, it will take effect after clear the cumulative quantity and the current quantity. (The parameter has been SET before delivery, do not greatly adjustment).
6、注意事項(Announcements)
1) 該機使用110伏交流電,接通電源前請檢查一下機器各部位零件是否安裝到位。
— This machine use 110V alternating current (AC), please check each part of the machine parts is installed before turning on the power supply.
2) 務必使導輪底部導帶環處于同一水平線上,上導帶環推至與標簽邊緣之位置。
— Make sure all guide wheel at the same level, push the top wheel to the edge of label.